"Biobased Lubricants that Perform Like Synthetics"

Bio Motor Oils, ATF, Gear

Bio-Ultimax 1000- 2000 Hydraulic Fluids (ISO 32, 46, 68)

Bio-Hydraulic Fluids, Bio-Ultimax™ 1000 & 2000, are ultimately biodegradable vegetable based formulas that replace mineral oil based hydraulic fluids.  Bio-Ultimax™ Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas).  Zinc-free additive systems have also been developed that are environmentally friendly and meet or exceed pump requirements.

Bio-Ultimax™ Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston, and gear-type pumps and have shown to have exceptional anti-wear performance.  Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S), and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 150⁰ to 210⁰ F.  The anti-wear performance exceeds the requirements for US Steel 126 and 127, load stage 10 in the FZG (DIN 51354), DIN 51524, and GM (LS-2).  They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges.  Bio-Ultimax™ AW 1000 meets and exceeds Federal Specifications A-A-59354 Superseding MIL-H-46001D.

Bio-Ultimax Hydraulic Fluids AW 1000 SAE 10W40

A specially formulated, ultimately biodegradable product designed for hydraulic driven systems that require a heavier SAE 40 viscosity for summer and fluid that passes the winter 10W viscosity for cold temperature pumpability protection (i.e.: approved by Hustler Mower Engineering for this OEM specifications).  Bio-Ultimax™ Hydraulic Fluid is formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties.  It is highly inhibited against moisture and rusting in both fresh and sea water and passes both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formula).  A zinc-free additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements. 

Bio-Ultimax™ Hydraulic Fluid is designed for use in mobile and stationary hydraulic vane, piston, and gear-type pumps and has shown exceptional anti-wear performance.  Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S), and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 150⁰ to 210⁰ F.  The anti-wear performance exceeds the load stage 10 in the FZG (DIN 51354) requirements for US Steel 136, DIN 51524, and GM (LS-2).  It also meets the requirements for ashless GL-3 gear oils in reduction units and gear sets where it meets the viscosity range.

Bio-Ultimax 1200LT Hydraulic Fluids (ISO 15, 22, 32)

Bio-Ultimax 1500 Dielectic Hydraulic Fluids (ISO 22, 32, 46, 68)

A specially formulated, ultimately biodegradable product designed specifically for use in hydraulic equipment operating over a wide range of temperatures and where an oil with high dielectric (>35 KV) insulating property is required.  Applications include power utility aerial lift buckets, mobile and stationary hydraulic systems, or other equipment where electrical insulating safety is preferred.  Bio-Ultimax 1500 Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties.  They are highly inhibited against moisture and rusting in both fresh and sea water and passes both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formula).  A zinc-free additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements.  

Bio-HVO Hydraulic Fluids (ISO 46, 68, FR)

Bio-HVO™ Hydraulic Fluids are ultimately biodegradable vegetable based formulas that meet and exceed Vickers M-2950-S, Vickers 1-286-5, U.S. Steel 126, U.S. Steel 127, and U.S. Steel 136.  Bio-HVO™ Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear, Anti-Rust, and Anti-Oxidation properties.  They have been USDA Biobased tested to show new carbon (vegetable based) at 96% to 100% and  specially formulated to offer the lowest toxicity in aquatic conditions. There anti-wear performance exceeds the requirements for Vickers 35VQ-25 and V-104C (ASTM D-2882) vane pump stand tests, and DIN 51524 Part 2 load stage 10.  They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formulas, gives multi-grade synthetic base oils performance by boosting the viscosity index to synthetic levels (Energy Conserving Formulas).  A zinc-free additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements.

Bio-HVO Hydraulic Fluids are excellent products for inner plant applications (steel mills) as a fire resistant (FR) hydraulic fluids, with excellent oxidation stability (RBOT 350-400 minutes) exceeding the US Steel minimum requirements of 120 minutes.  Although the Bio-HVO provide pour points of -25^o C, care must be taken when setting static below freezing for extended periods.

Bio-HVO2 Hydraulic Fluids (ISO 46, 68, FR)

Bio-HVO2™ Hydraulic Fluids are ultimately biodegradable vegetable based formulas that meet and exceed Vickers M-2950-S, Vickers 1-286-5, U.S. Steel 126, U.S. Steel 127, and U.S. Steel 136.  Bio-HVO2™ - Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear, Anti-Rust, and Anti-Oxidation properties.  They have been USDA Biobased tested to show new carbon (vegetable based) at 96% to 100% and  specially formulated to offer the lowest toxicity in aquatic conditions.  There anti-wear performance exceeds the requirements for Vickers 35VQ-25 and V-104C (ASTM D-2882) vane pump stand tests, and DIN 51524 Part 2 load stage 10.  They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formulas, gives multi-grade synthetic base oil performance by boosting the viscosity index to synthetic levels (Energy Conserving Formulas). A zinc-free additive system has also been developed that is environmentally friendly and meets or exceeds Vickers and Denison pump performance.

Bio-HVO2™ Hydraulic Fluids are excellent products for inner plant applications (steel mills) as a fire resistant (FR) hydraulic fluids, with excellent oxidation stability (RBOT 200-250 minutes) exceeding the US Steel minimum requirements of 120 minutes.  Bio-HVO2 provides improved cold temperature over Bio-HVO and competitors with equal biobase content.  Although the Bio-HVO2 provide pour points of  -25^o C and -30^o C, care must be taken when setting static below -10^o C for extended periods.

Bio-Hydraulic™ Fluids (ISO 32, 46, 68)

Bio-Hydraulic™ Fluids are ultimately biodegradable¹ vegetable based formulas that meet and exceed Vickers M-2950-S, Vickers 1-286-5, U.S. Steel 126, and U.S. Steel 127.  Bio-Hydraulic™ Fluids are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties.  There anti-wear performance exceeds the requirements for Vickers 35VQ-25 and V-104C (ASTM D-2882) vane pump stand tests, and DIN 51524 Part 2 load stage 10.  They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges.   Bio-Hydraulic™ Fluids are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Bio-Hydraulic Fluids were one of Renewable Lubricants' first hydraulic fluids in the market and have been well tested.  Bio-Hydraulic Fluids have been used  in many applications including, blow-out oil for off shore drilling.

Bio-MIL-PRF-32073 Hydraulic Fluids (ISO 15, 22, 32, 46, 68)

Bio-MIL-PRF-32073 Hydraulic Fluids are ultimately biodegradable¹ vegetable biobased formulas that were designed specifically to replace mineral oil based hydraulic fluids for environmentally sensitive areas.  They have been specifically formulated to provide additional seal swell (10% to 30%) as required by MIL-PRF-32073.  Bio-MIL-PRF-32073 Hydraulic Fluids are formulated to perform in hydraulic systems that require anti-wear, anti-foam, anti-rust, anti-oxidation, and demulsibility properties.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, gives multi-grade synthetic base oil performance by boosting the viscosity index to synthetic levels.  This super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and increases load capacity.  The HOBS’s extremely low volatility increases the flash and fire safety features in the formula.  A zinc-free additive system has also been developed that is environmentally friendly and exceeds the load stage 10 in the FZG (DIN51354) requirements for both turbine oils and reduction gears.  They also meet the requirements for an ashless GL-3 gear oil.  Bio-MIL-PRF-32073 Hydraulic Fluids are ENVIRONMENTALLY RESPONSIBLE products that are formulated from renewable agricultural plant resources.  We believe Earth's environmental future rests in the use of renewable materials.

Bio-AW/AL Hydraulic Press Oils (ISO 32, 46, 68)

Bio-AW/AL™ Hydraulic Press Oils are ultimately biodegradable vegetable based formulas that replace mineral oil based hydraulic fluids in demanding press hydraulic systems.  Bio-AW/AL™ Hydraulic Press Oils are formulated to perform in hydraulic systems that require Anti-Wear (AW), Anti-Leak (AL), anti-rust, anti-oxidation, anti-foam, and demulsibility properties.  Bio-AW/AL™ Hydraulic Press Oils contain the same performance benefits and additive technology as the Bio-Ultimax™ 1000 Hydraulic Fluids with the addition of the anti-leak and/or non-drip performance.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas).  A zinc-free (ashless) additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements.

Bio-AW Turbine R & O Fluids (ISO 32, 46, 68, 100)

Bio-AW Turbine™ R & O Fluids are ultimately biodegradable vegetable based formulas that were designed specifically to replace mineral oil based turbine oils in environmentally sensitive hydroelectric (water) turbine bearings.  These bearings are subject to humid/ moist conditions because of occasional seal leakage, but operate cooler than gas and steam turbine bearings.  Bio-AW Turbine™ Fluids are formulated to perform in R & O systems that require anti-foam, anti-rust, anti-oxidation, and demulsibility properties.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.   The Bio-AW Turbine R & O Fluids provide the same pump and gear performance as the Bio-Ultimax Hydraulic Fluids above.

All contents copyrighted 2008, Renewable Lubricants ^TM, Inc.

Patented Products: US Patent 5,736,493, US Patent 5,863,872, US Patent 5,990,055, US Patent 6,383,992, US Patent 6,534,454,  US Patent 6,624,124, US Patent 6,620,772 with additional Pending and Foreign Patents

All rights reserved