Bio-Ultimax™ Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas).  Zinc-free additive systems have also been developed that are environmentally friendly and meet or exceed pump requirements.

Bio-Ultimax™ Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston, and gear-type pumps and have shown to have exceptional anti-wear performance.  Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S), and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 1500 to 2100 F.  The anti-wear performance exceeds the requirements for US Steel 126 and 127, load stage 10 in the FZG (DIN 51354), DIN 51524, and GM (LS-2).  They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. 

An environmentally friendly, zinc-free additive system has also been developed that meets or exceeds high pressure pump requirements. The anti-wear performance meets the requirements for Vickers 35VQ-25 and V-104C (ASTM D-2882) vane pump stand tests, and exceeds DIN 51524 Part 2 load stage 10 that is recommended for piston and gear pumps. Bio-Fleet™ Hydraulic Fluids are the perfect economical choice for hydraulic equipment operating outside, where unpredictable higher moisture and dusty environments are more prominent and the equipment require more frequent oil change intervals. They are highly inhibited against moisture and rusting in both fresh and sea water, passed both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test, and they provide excellent water separation as shown in ASTM D-1401 Demulsibility Test.

A zinc-free additive system has also been developed that is environmentally friendly and meets most pump requirements. Although this formula will not have the cold temperature performance and oxidation stability of the Bio-Series Hydraulic Fluids, it does give acceptable performance over low erucic rapeseed oil formulas and was designed to operate in applications where temperatures reach less than 900 C. In a comparative study, the commercial rapeseed formula produced a Rotary Bomb Oxidation Test (RBOT) ASTM D-2272 of 27 minutes while the BHHO formula outperformed the commercial rapeseed formula at a RBOT time of 150 minutes.

Bio-Ultimax™ Hydraulic Fluid is formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties.  It is highly inhibited against moisture and rusting in both fresh and sea water and passes both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formula).  A zinc-free additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements. 

Bio-Ultimax™ Hydraulic Fluid is designed for use in mobile and stationary hydraulic vane, piston, and gear-type pumps and has shown exceptional anti-wear performance.  Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S), and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 1500 to 2100 F.  The anti-wear performance exceeds the load stage 10 in the FZG (DIN 51354) requirements for US Steel 136, DIN 51524, and GM (LS-2).  It also meets the requirements for ashless GL-3 gear oils in reduction units and gear sets where it meets the viscosity range.

Bio-Ultimax™ 1200LT Hydraulic Fluids are formulated to perform in hydraulic systems that require anti-wear, anti-foam, anti-rust, anti-oxidation, and demulsibility properties.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, gives multi-grade synthetic base oil performance by boosting the viscosity index (VI) past synthetic levels (energy conserving formulas).  This super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and increases load capacity.  They provide additional fluid value at the higher temperatures, which is a performance benefit over lower VI products of the same ISO viscosity.  The HOBS’s extremely low volatility increases the flash and fire safety features in the formula compared to petroleum formulations with the same viscosity ranges.  A zinc-free additive system has also been developed that is environmentally friendly and exceeds the load stage 10 in the FZG (DIN51354) requirements for low viscosity hydraulic and turbine oils.  They may be used in reduction gears for cold temperature applications, where the OEM recommends a lighter viscosity or SAE 0W for proper channeling.  Bio-Ultimax™ 1200LT Hydraulic Fluids are ENVIRONMENTALLY RESPONSIBLE products that are formulated from renewable agricultural plant resources.  We believe Earth's environmental future rests in the use of renewable materials.

Applications include power utility aerial lift buckets, mobile and stationary hydraulic systems, or other equipment where electrical insulating safety is preferred.  Bio-Ultimax 1500 Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties.  They are highly inhibited against moisture and rusting in both fresh and sea water and passes both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formula).  A zinc-free additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements.  

Bio-Ultimax™ 1500 Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston, and gear-type pumps and has shown exceptional anti-wear performance.  Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S), and V-104C (ASTM D-2882) pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 1500 to 2100F.  The anti-wear performance exceeds the load stage 10 in the FZG (DIN 51354) requirements for US Steel 136, DIN 51524, and GM (LS-2).  It also meets the requirements for ashless GL-3 gear oils in reduction units and gear sets where it meets the viscosity range.

Bio-HVO™ Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear, Anti-Rust, and Anti-Oxidation properties.  They have been USDA Biobased tested to show new carbon (vegetable based) at 96% to 100% and  specially formulated to offer the lowest toxicity in aquatic conditions. There anti-wear performance exceeds the requirements for Vickers 35VQ-25 and V-104C (ASTM D-2882) vane pump stand tests, and DIN 51524 Part 2 load stage 10.  They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formulas, gives multi-grade synthetic base oils performance by boosting the viscosity index to synthetic levels (Energy Conserving Formulas).  A zinc-free additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements.

Bio-HVO Hydraulic Fluids are excellent products for inner plant applications (steel mills) as a fire resistant (FR) hydraulic fluids, with excellent oxidation stability (RBOT 350-400 minutes) exceeding the US Steel minimum requirements of 120 minutes.  Although the Bio-HVO provide pour points of -25° C, care must be taken when setting static below freezing for extended periods.

Bio-HVO2™ - Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear, Anti-Rust, and Anti-Oxidation properties.  They have been USDA Biobased tested to show new carbon (vegetable based) at 96% to 100% and  specially formulated to offer the lowest toxicity in aquatic conditions.  There anti-wear performance exceeds the requirements for Vickers 35VQ-25 and V-104C (ASTM D-2882) vane pump stand tests, and DIN 51524 Part 2 load stage 10.  They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.   Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formulas, gives multi-grade synthetic base oil performance by boosting the viscosity index to synthetic levels (Energy Conserving Formulas). A zinc-free additive system has also been developed that is environmentally friendly and meets or exceeds Vickers and Denison pump performance.

Bio-HVO2™ Hydraulic Fluids are excellent products for inner plant applications (steel mills) as a fire resistant (FR) hydraulic fluids, with excellent oxidation stability (RBOT 200-250 minutes) exceeding the US Steel minimum requirements of 120 minutes.  Bio-HVO2 provides improved cold temperature over Bio-HVO and competitors with equal biobase content.  Although the Bio-HVO2 provide pour points of  -25° C and -30° C, care must be taken when setting static below -10° C for extended periods.

Bio-Hydraulic™ Fluids are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties.  There anti-wear performance exceeds the requirements for Vickers 35VQ-25 and V-104C (ASTM D-2882) vane pump stand tests, and DIN 51524 Part 2 load stage 10.  They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges.   Bio-Hydraulic™ Fluids are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Bio-Hydraulic Fluids were one of Renewable Lubricants' first hydraulic fluids in the market and have been well tested.  Bio-Hydraulic Fluids have been used  in many applications including, blow-out oil for off shore drilling.

Specifically formulated to provide additional seal swell (10% to 30%) as required by MIL-PRF-32073.  Bio-MIL-PRF-32073 Hydraulic Fluids are formulated to perform in hydraulic systems that require anti-wear, anti-foam, anti-rust, anti-oxidation, and demulsibility properties.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, gives multi-grade synthetic base oil performance by boosting the viscosity index to synthetic levels.  This super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and increases load capacity.  The HOBS’s extremely low volatility increases the flash and fire safety features in the formula.  A zinc-free additive system has also been developed that is environmentally friendly and exceeds the load stage 10 in the FZG (DIN51354) requirements for both turbine oils and reduction gears.  They also meet the requirements for an ashless GL-3 gear oil.  Bio-MIL-PRF-32073 Hydraulic Fluids are ENVIRONMENTALLY RESPONSIBLE products that are formulated from renewable agricultural plant resources.  We believe Earth's environmental future rests in the use of renewable materials.

Bio-AW/AL™ Hydraulic Press Oils are formulated to perform in hydraulic systems that require Anti-Wear (AW), Anti-Leak (AL), anti-rust, anti-oxidation, anti-foam, and demulsibility properties.  Bio-AW/AL™ Hydraulic Press Oils contain the same performance benefits and additive technology as the Bio-Ultimax™ 1000 Hydraulic Fluids with the addition of the anti-leak and/or non-drip performance.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.  Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas).  A zinc-free (ashless) additive system has also been developed that is environmentally friendly and meets or exceeds pump requirements.

These bearings are subject to humid/ moist conditions because of occasional seal leakage, but operate cooler than gas and steam turbine bearings.  Bio-AW Turbine™ Fluids are formulated to perform in R & O systems that require anti-foam, anti-rust, anti-oxidation, and demulsibility properties.  They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test.   The Bio-AW Turbine R & O Fluids provide the same pump and gear performance as the Bio-Ultimax Hydraulic Fluids above.